吸附式干燥机介绍：

1、设计精良的吸附塔体

　　接触时间达6.25秒的大型吸剂床层，确保进入干燥机的饱和空气干燥至所需的 露点，并补偿吸附剂层的自然老化；

　　结构可靠的大型不锈钢气流扩散器，确保气流均匀通过吸附剂层，消除沟流现象；

　　合适的塔体尺寸和上游干燥下游再生的对流方式，有利于减少再生气用量，并避免吸附剂流化和吸附剂层受污染；

　　缓慢而完全的充压程序和延时切换设计，消除下游气流脉动现象，并防止吸附剂移动和吸附剂磨蚀；

　　独立的充填口和排出口，便于更换吸附剂；

　　塔体制造符合压力容器国标规范。

2、高性能的活性氧化铝吸附剂

　　抗压强度高，抗磨蚀，耐高温，不水解；

　　比表面积和静态吸附量大。

3、效果良好的消音器

　　对称设置，减弱噪声叠加效应；

　　特设减压箱，消音器装拆方便，消声效果好。

4、独具功率大和耐用两大特点的进口气动控器

　　采用二位五通先导阀和经深度干燥、过滤的控制气，确保精确控制；

　　双活塞结构，气动功率大，动作可靠、反应快；

　　控制器与主气流隔离，免受潮气污染。

5、耐用可靠的进口气动蝶阀进气阀和再生/再加压阀

　　弹性体阀座、薄型镀镍阀盘，确保无泄漏运行，并提供低压降；

　　阀杆轴衬确保平滑运转，无需现场润滑。 6、可精确调节流量的再生气调节阀

　　独特的平衡阀口设计，确保精确调节；

　　气流始终以同一方向通过阀门，确保流动稳定一致；

　　调节阀和节流孔板分开设置，易于控制再生气流量。

7、可靠的止回阀

　　采用软性阀座，确保正确闭合、减少磨损，且耐高温，使用寿命长。

8、安全性佳 维修容易

　　符合压力容器标准；

　　整台设备经喷砂防锈处理不易腐蚀；

　　尼龙软管承受压力为1.5MPa（40℃）；

　　表接可做阀门使用，易于更换压力表；

　　活动式管接，维修容易。

Adsorption type dryer is introduced:

1, design sophisticated adsorption tower

The contact time of 6.25seconds of large suction agent bed layer, ensure into the dryer saturated air drying to the desired dew point, and compensation of adsorbent layer of natural aging;

Structural reliability of large stainless steel air diffuser, ensure the flow evenly through the adsorbent layer, remove channeling phenomenon;

The appropriate dimension of tower body and upstream downstream regenerated convection drying, can reduce the dosage of regeneration, and avoid the adsorbent fluidized and adsorbent layer contaminated;

Slow and complete filling pressure and delay switch design, eliminating the downstream gas pulsation phenomenon, and to prevent the adsorbent mobile and adsorbent abrasion;

Independent filling inlet and outlet, easy replacement of adsorbent;

The tower body manufacturing in line with pressure vessels GB standard.

In 2, a high performance activated alumina adsorbents

High compressive strength, abrasion resistance, high temperature resistance, not hydrolysis;

The specific surface area and the static adsorption quantity.

3, good effect of the muffler

Symmetrically, weakening noise superposition effect;

Ad hoc decompression silencer box, convenient assembly and disassembly, good silencing effect.

4, the unique power and durability characteristics of the two imported pneumatic controller

The two position five way valve and the depth of drying, filtration control gas, ensure accurate control;

Double piston structure, large pneumatic power, reliable operation, fast response;

The controller with the main air flow isolation from humidity, pollution.

5, durable and reliable pneumatic butterfly valve inlet valve and regeneration / repressurization valve

Elastic body seat, thin nickel valve disc, to ensure that no leakage of operation, and provides a low pressure drop;

Stem bushing to ensure smooth operation, without on-site lubrication. In 6, can be precisely regulated flow regulating valve and angry

Unique balance valve port design, ensure accurate adjustment;

Air flow through the valve is always in the same direction, ensure the flow stability and consistency;

Regulating valve and throttle orifice plate are separately arranged, easy control and gas flow rate.

In 7, the reliable check valve

Adopting soft seat, ensure proper closure, less wear, high temperature resistance, long service life.

8, good safety easy repair

Conform to the standards for pressure vessel;

The whole device by sandblasting rust corrosion;

Nylon hose pressure was 1.5MPa (40 degrees C );

Table connected to valve, easy replacement of pressure gauge;

Activity type pipe joint, easy repair.

更多的吸附式干燥机产品可以点击//www.dsbgzj.com/浏览。