设备安装加固技改加固危房改造加固钢结构预埋件高强灌浆料

商家:
广西新汇联建材有限公司
认证:
普通商家
参考价:
面议
地区:
广西 - 南宁
类别:
新型建材 - 新特建材
品牌:
新汇联  
产地:
广西南宁  
型号:
KL-60A  
给我留言
商家有16个相似产品 上一条 11 12 13 14 15 16 切换到相册模式

产品描述

 更新于 2026-11-18 08:27:01 查看商家信息
材质粉状 产品类别灌浆料
功能高强早强无收缩二次加固灌浆料厂家直销 规格40KG
适用范围设备安装加固,技改加固,危房改造加固,钢结构预埋件高强灌浆料

广西新汇联建材有限公司

GUANGXI XINHUILIAN BUILDING MATERIALS CO.,LTD.

新型聚合物高强早强灌浆料

New Polymer High-Strength Early-Strength Grouting Material

超级混凝土·高强早强·无收缩微膨胀·自密实免振捣 | Super Concrete ·High &Early Strength ·Non-Shrink ·Self-Compacting

1.产品简介/PRODUCT OVERVIEW

新型聚合物高强早强灌浆料(俗称“超级混凝土”)以高强水泥为胶结基材,复配聚合物改性组分、高强度级配骨料、微膨胀组分与高性能减水剂,经工厂预混而成的干粉砂浆材料。现场按比例加水搅拌即可使用,加水后呈高流态自流平态,无需振捣即可自动填充设备基础、螺栓孔与结构缝隙的全部空隙;硬化后形成高强、致密、无收缩的承载层,抗压强度可达C50–C100 等级,广泛用于需要“超级混凝土”的各类工程。执行标准:GB/T 50448-2015《水泥基灌浆材料应用技术规范》。

Known as“Super Concrete”,this material is a factory-premixed dry mortar made of high-strength cement as binder,compounded with polymer-modified components,high-strength graded aggregates,micro-expansion agents and high-performance superplasticizers.Simply add water on site and mix;the fresh mix is highly flowable and self-leveling,filling equipment foundations,bolt holes and structural gaps completely without vibration.After hardening it forms a high-strength,dense ,non-shrinking bearing layer with compressive strength of C50–C100.Standard:GB/T 50448-2015.

2.产品优势/KEY FEATURES

?早强高强1-day compressive strength ≥50 MPa;ready for loading 24 h after pouring

?无收缩微膨胀Micro-expansion 3h ≥0.02%,compensates shrinkage,no voids

?自密实免振捣Self-compacting ,fills complex cavities without vibration

?高流动度Initial flow ≥300 mm ,retained ≥290 mm at 30 min

?高粘结强度Strong bond to old concrete and steel ,≥2 .8 MPa

?抗油渗无锈蚀Chloride-free,no corrosion to rebar or equipment

?耐久耐候200 million fatigue cycles and 50 freeze-thaw cycles without decay

?绿色环保Non-toxic,odorless,non-flammable ,indoor/outdoor/underground use

3.应用领域/APPLICATIONS

**于需要高强“超级混凝土”的各类工程:大型设备基础一次/二次灌浆与安装加固(机床、风机、轧机、压缩机、汽轮机等);危房与既有结构加固改造(梁柱节点、承重墙、地基空腔、钢筋锚固与植筋);桥梁与道路工程(桥梁支座垫石、盆式支座、桥面与路面高强修补、隧道与涵洞接缝);钢结构柱脚与地脚螺栓锚固;地铁、机场、电厂、码头及灾后快速抢修工程。也适用于灌浆层厚度≥30 mm、需免振捣自流密实的各种场合。

For all works requiring high-strength“super concrete”:primary and secondary grouting and installation reinforcement of large equipment foundations(machine tools ,fans,rolling mills,compressors,turbines);reinforcement and renovation of dilapidated and existing structures (beam-column joints,loadbearing walls,foundation cavities,rebar anchorage);bridge and road works (bearing pads,pot bearings,high-strength pavement repair,tunnel and culvert joints);steel-column bases and anchor-bolt anchoring;subways ,airports ,power plants,wharves and rapid post-disaster repair.Also for any grouting layer≥30 mm requiring self-leveling compaction without vibration.

广西新汇联建材有限公司| 新聚合物材料| www.gxxhl.com

4.典型技术指标/TYPICAL TECHNICAL DATA

项目Item

指标Specification

外观Appearance

灰色均匀干粉/Grey uniform dry powder

流动度(初始)Initial flowability

≥300 mm

30 min 流动度保留值Retained flow @30min

≥290 mm

抗压强度1d /3d /28d Compressive strength

≥50 /≥70 /≥100 MPa(C50–C100 可选)

竖向膨胀率(3h)Vertical expansion

≥0.02%

24h 与3h 膨胀率差值Expansion difference

≤0.05%

泌水率Bleeding rate

0%(无泌水/no bleeding)

初凝时间Initial setting time

≤3 h

粘结强度Bond strength

≥2.8 MPa

钢筋握裹强度(圆钢/螺纹钢)Bond to rebar

≥6.0 /≥13.0 MPa

氯离子含量Chloride ion content

≤0.03%

抗冻融/抗疲劳Freeze-thaw /Fatigue

50 次/200 万次无强度衰减/no decay

水料比Water-to-powder ratio

12%–14%(推荐13%/recommended 13%)

容重Bulk density

2280–2400 kg/m?

适用温度Service temperature

-5℃–40℃

注:以上为25℃标准养护条件下的典型值,实际指标以出厂检测报告及产品技术数据表(TDS)为准。 Note:Typical data under standard curing at 25℃;actual data is subject to the factory test report and product TDS.

5.强度等级选型/STRENGTH GRADE SELECTION

型号Model

强度等级Grade

适用场景Application

KL-60A

C60

通用设备基础二次灌浆(24h≥22 MPa,28d≥70 MPa)/General equipment foundations

KL-C80 /KL-C100

C80 /C100

重型设备、钢结构柱脚、风电核电、高精密机床、抢修/Heavy equipment ,steel bases,wind&nuclear,emergency repair

KL-600 /KL-50A

支座/轨道型

桥梁支座垫石、轨道垫石**/Bridge bearings and track pads

广西新汇联建材有限公司| 新聚合物材料| www.gxxhl.com

6.使用方法(施工工艺) /HOW TO USE (APPLICATION METHOD)

6.1 施工准备与条件/Preparation &Conditions

?机具:强制式搅拌机或**搅拌器、电子秤、灌浆漏斗与溜槽、模板、抹刀、湿布/塑料薄膜等养护材料。 Tools:forced mixer or dedicated agitator,scale,funnel and chute,formwork ,trowel ,wet cloth /plastic film.

?环境:温度-5℃~40℃(**佳15–30℃),雨雪天不得灌浆;低温施工用温水搅拌(≤60℃)并保温蓄热。 Environment:-5℃~40℃(15–30℃best);no grouting in rain or snow;use warm water (≤60℃)and heat insulation in cold weather.

?基层:提前24 h 充分润湿基面,灌浆前1 h 清除积水,保持湿润无明水。 Substrate:pre-wet 24 h in advance;remove standing water 1 h before grouting;keep damp but without free water.

6.2 施工步骤/Application Steps

第1 步基层处理 Step 1 Substrate preparation 清除基础表面碎石、浮浆、浮灰、油污与脱模剂;混凝土基面凿毛(深度≥5 mm)并露出坚硬基面;地脚螺栓孔壁清理干净并提前8–12 h 用水浸泡湿润。

Remove debris,laitance ,dust,oil and release agent;chisel the concrete surface (≥5 mm)to expose sound aggregate;clean bolt holes and soak them 8–12 h in advance.

第2 步支模 Step 2 Formwork 按施工图支设模板,模板与设备底座四周水平距离约100 mm;模板顶面高出设备底座上表面≥50 mm;模板接缝用密封胶或水泥砂浆封堵严密,防止漏浆。

Erect formwork per drawings,about 100 mm from the base on all sides;the formwork top shall be ≥50 mm above the base top;seal all joints to prevent leakage.

第3 步搅拌 Step 3 Mixing 按水料比12%–14%称量用水;先加2/3 水量,再缓慢加入灌浆料,机械搅拌2–3 min;加入剩余水量继续搅拌至均匀无结块,总搅拌时间≥3 min;静置2–3 min 消泡后使用。

Weigh water at 12%–14%of powder;add 2/3 of the water first,then slowly add the powder and mix 2–3 min;add the rest and mix until uniform ,total ≥3 min;let stand 2–3 min to de-foam.

第4 步灌浆 Step 4 Grouting 从灌浆腔一侧连续注入,直至另一侧溢出,禁止四侧同时灌浆;利用自重法(或高位漏斗法,自由落差≤1 .5 m)自流填充;灌浆必须连续不得中断;必要时用竹板沿底部推动,严禁振捣。

Pour continuously from one side until it overflows the opposite side;never pour from all sides at once.Use the gravity method (or hopper method ,drop≤1 .5 m).Keep it continuous;push along the bottom with a bamboo board if needed;never vibrate.

第5 步表面处理 Step 5 Surface finishing 灌浆完毕后,在初凝前将外露表面压光;灌浆后3–6 h 沿设备边缘向外切45°斜角,防止自由端产生裂缝。

Before initial set,trowel the exposed surface smooth;3–6 h after grouting,cut a 45°chamfer outward along the equipment edge to prevent edge cracking.

第6 步养护 Step 6 Curing 灌浆完毕30 min 内覆盖塑料薄膜或湿布保湿,养护不少于7 天;养护期避免振动、冲击与积水;环境温度<5℃时采取保温措施。

Cover with plastic film or wet cloth within 30 min and cure for at least 7 days;avoid vibration,impact and standing water;take insulation measures when below 5℃.

第7 步拆模与加载 Step 7 Formwork removal &loading 常温(20℃)下拆模时间不少于24 h;24 h 强度即达承载要求,可进行设备安装与后续施工;冬期养护应符合JGJ 104 规定。

Remove formwork after at least 24 h at 20℃;24-hour strength already meets load requirements for equipment installation;winter curing shall comply with JGJ 104.

6.3 施工注意事项/Application Notes

?严格按水料比加水,严禁额外加水或掺入任何外加剂、外掺料。 Follow the water-to-powder ratio strictly;never add extra water or any admixture.

?每次搅拌量以30 min 内用完为准;已干燥或初凝的浆料不得再加水使用。 Mix only what can be used within 30 min;never re-temper dried or set material.

?灌浆层厚度>150 mm 时,宜采用豆石型产品或分层灌注(每层≤100 mm)。 For layers >150 mm ,use the pea-gravel type or pour in layers(≤100 mm each).

?大体积、长距离灌浆应分段施工,单侧连续灌注,流动距离宜≤5 m。 For large or long pours,work in sections from one side ,flow distance ≤5 m.

?灌浆层达到拆模强度后方可加载;设备二次灌浆后应停机24–36 h,避免振动传给未结硬的灌浆层。 Load only after the grout reaches formwork-removal strength;stop the machine 24–36 h after secondary grouting.

7.包装、储存与参考用量/PACKAGING,STORAGE &DOSAGE

?包装:40kg/袋(防潮编织袋),可提供50 kg/袋及外贸定制包装。 Packaging:40 kg/bag (kraft-paper composite or moisture-proof woven bag);50 kg/bag and custom export packaging available.

?储存:置于阴凉、干燥、通风处,防潮防雨淋,避免阳光直射;未开封保质期6 个月,超期经复检合格仍可使用。 Storage:keep cool , dry and ventilated ,away from moisture,rain and sunlight;shelf life 6 months,usable after passing re-inspection.

?参考用量:容重约2.28–2.4 t/m?,1 m?灌浆体约需2 .28–2.4 吨(约92–96 袋);每袋40kg 约可灌注0.010–0.011 m?(约10–11

L),实际用量按空隙体积与损耗计算。 Dosage:bulk density about 2.28–2.4 t/m?,i.e.2.28–2.4 t (about 92–96 bags)per m?;each 25 kg bag fills

about 0.010–0.011 m?(10–11 L).Compute by cavity volume and loss.

广西新汇联建材有限公司| 新聚合物材料| www.gxxhl.com

 袋子叠一起大量图片
袋子叠一起大量图片

 fV44otsBj - 副本
fV44otsBj - 副本

 微信图片_20240803063405
微信图片_20240803063405

以上是设备安装加固技改加固危房改造加固钢结构预埋件高强灌浆料的详细介绍,包括设备安装加固技改加固危房改造加固钢结构预埋件高强灌浆料的厂家、价格、型号、图片、产地、品牌等信息!
联系姓名
李玉锋
联系电话
153078***** 点击查看
联系地址
广西西乡塘区安宁街道永宁村
商家主页
https://shop.jc001.cn/1526110/
官方网站
电子邮箱

>> 了解更多信息

1、您想了解更多的商家信息吗? 可以点击按钮,了解更多详细。

详细联系方式 商家网站 给商家留言

2、您可以请点击按钮,查看更多新特建材商家。

3、想查点看更多产品信息,可以查看 新特建材产品库,了解更多。

4、在线联系

新型建材商家推荐

更多商家推荐 >>

四川顺美新材料有限公司

Tel:

嘉宝莉 外墙抗碱底漆  水性封闭型底漆

¥12.00元

嘉宝莉自洁防尘面漆 水性透明罩面保护漆

¥220.00元

嘉宝莉真石漆 水性砂质感外墙装饰涂料

¥118.00元

成都特瓦新材料有限公司

Tel:

虹吸排水系统

¥面议

成品排水沟—线性排水沟

¥面议

格栅式-树脂排水沟

¥面议

南京三元新型建材厂

Tel:

南京隔墙板-三元轻质复合隔墙板

¥面议

南京隔墙板-三元轻质复合隔墙板

¥面议

南京隔墙板-三元轻质复合隔墙板(FPB板)

¥面议

南京天亚新材料有限公司.

Tel:

HL301X桥梁修复灌浆料-桥梁类产品

¥面议

空心板梁抗剪加固超韧性腔内灌注料-桥梁类产品

¥面议

HL速硬抗裂伸缩缝抢修料-桥梁类产品

¥面议

留言咨询

关于九正 会员服务 广告服务 访客留言 企业邮箱 网站地图 建材专栏 地区专栏 产品归档 产品地图 服务条款
九正建材网 版权所有©2000-2026      九正建材网全国免费服务热线:400 6464 001 传真:028-83370196